Description
The FT-MTRS-2S60-01 is a very compact 10Gb/s optical transceiver module for serial optical communication applications at 10Gb/s. The MTRS-2S60-01 series converts a 10Gb/s serial electrical data stream to 10Gb/s optical output signal and a 10Gb/s optical input signal to 10Gb/s serial electrical data streams. The high speed 10Gb/s electrical interface is fully compliant with XFI specification (built in CDR on both TX and RX) and allows FR4 host PCB trace up to 200mm. The FT-MTRS-2S60-01 is designed for use in a variety of 10Gb/s equipment SDH/SONET (9.95Gb/s), Ethernet LAN (10.3Gb/s) and FC (10.5Gb/s). The customer can adjust interface electrical level to select 9.95G~11.3G rate section. The high performance 1550nm DFB transmitter coupled with a high sensitivity PIN receiver provide superior performance for applications up to 40km SMF.The fully compliant SFP form factor provides high density applications, hot plug ability easy optical port upgrades and low EMI emission.
The SFP+ ER with CDR module electrical interface is compliant to XFI electrical specifications. The transmitter input and receiver output impedance is 100Ohms differential. Data lines are internally AC coupled.The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI.
Features
¡ñ 10Gb/s serial optical interface compliant to SONET OC-192/SDH STM-64 and 802.3ae
¡ñ Electrical interface compliant to SFF-8431 specifications for 10 Gigabit small form factor pluggable module “SFP+”
¡ñ 1550nm cooled EML transmitter with TEC, PIN receiver
¡ñ 2-wire interface for management specifications compliant with SFF-8472 digital diagnostic monitoring interface for optical transceivers
¡ñ Operating case temperature: 0°C~70°C
Applications
¡ñ SONET(OC-192)/SDH(STM-64) line card
¡ñ 10GBASE-ER (10.3125Gbps)
¡ñ 10GBASE-EW (9.953Gbps)
Compliance
¡ñ Compliant with IEEE 802.3ae-2002 10G Base-ER
¡ñ Compliant with SFF-8431 & SFF-8432 & SFF-8472
Specification
Table1-Absolute Maximum Ratings |
||||
Paramete |
Symbol |
Min. |
Max. |
Unit |
Storage Temperature |
Ts |
-40 |
+85 |
¡æ |
Operating Case Temperature |
Tc |
-5 |
+75 |
¡æ |
Supply Voltage |
Vcc |
0 |
+4 |
V |
Relative Humidity |
RH |
+5 |
+85 |
% |
Rx Input Average Power |
Pmax |
- |
0 |
dBm |
Table2-Recommended Operating Conditions |
|||||
Paramet |
Symbol |
Min. |
Typical |
Max. |
Unit |
Operating Case Temperature |
TC |
0 |
25 |
+70 |
¡æ |
Power Supply Voltage |
VCC3 |
3.135 |
3.3 |
3.465 |
V |
Power Supply Current |
ICC3 |
- |
- |
545 |
mA |
Power Consumption |
|
- |
- |
1800 |
mW |
Table3-Transmitter Operating Characteristic-Optical |
|
||||||
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
Note |
|
Operating Data Rate |
DR |
9.95 |
- |
11.3 |
Gb/s |
|
|
Output Center Wavelength |
λ c |
1530 |
1550 |
1565 |
nm |
|
|
Side Mode Suppression Ratio |
SMSR |
30 |
|
- |
dB |
|
|
Average Output Power |
Po |
-1 |
|
+2 |
dBm |
|
|
Disabled Power |
Poff |
- |
|
-30 |
dBm |
|
|
Extinction Ratio |
ER |
8.2 |
|
- |
dB |
|
|
Eye Mask (@SONET/SDH) |
- |
5% (1000 consecutive snapshots at typical rate and room temperature) |
% |
|
|
||
Generation Jitter 1 (20kHz - 80MHz) |
- |
- |
- |
0.3 |
UIp-p |
|
|
Generation Jitter 2 (4MHz - 80MHz) |
- |
- |
- |
0.1 |
UIp-p |
|
|
Relative Intensity Noise |
RIN |
- |
- |
-128 |
dB/Hz |
|
|
Operating Distance |
- |
- |
40 |
- |
km |
|
|
Transmitter and dispersion penalty |
- |
- |
- |
2 |
dB |
|
|
Spectral Width |
- |
- |
- |
0.5
|
nm |
|
|
Dispersion tolerance |
Dt |
- |
- |
800 |
Ps/nm |
|
|
Optical return loss tolerance |
- |
|
|
21 |
dB |
|
Table4-Receiver Operating Characteristic-Optical |
||||||
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
Note |
Operating Data Rate |
- |
9.95 |
- |
11.3 |
Gb/s |
|
Input Center Wavelength |
lrc |
1260 |
|
1605 |
nm |
|
Overload |
Rovl |
-1 |
- |
- |
dBm |
|
Minimum Sensitivity |
Rsen |
- |
- |
-16 |
dBm |
|
RX_LOS Assert Level |
RLOSa |
-28 |
- |
- |
dBm |
|
RX_LOS Deassert Level |
RLOSd |
- |
- |
-18 |
dBm |
|
RX_LOS Hysteresis |
RLOSh |
0.5 |
- |
|
dB |
|
Optical Return Loss |
ORL |
- |
- |
-27 |
dB |
|
Table 5-Eelectrical characteristics |
|||||||
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
Note |
|
Input differential impedance |
- |
|
100 |
|
Ω |
|
|
Differential data input swing |
VI |
180 |
|
700 |
mV |
|
|
Differential data output swing |
V0 |
300 |
|
850 |
mV |
|
|
Tx Fault, LOS Output Voltage |
High Low |
- |
2.4 |
|
Vcc |
V |
|
Low |
- |
Vee |
|
Vee+ 0.4 |
V |
|
|
Tx DisableRS0,RS1 |
Low High |
VIL
|
Vee-0.3 |
|
Vee+ 0.8 |
V |
|
High |
VIH |
2 |
|
Vcc+0.3 |
V |
|
DITITAL DIAGNOSTIC FUNCTIONS
The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless therwise specified. It is compliant to SFF-8472 Rev10.4 with internal calibration mode. For external calibration mode please contact our sales stuff.
Table 6- Digital diagnostic specification table
|
|||||
Parameter |
Symbol |
Min. |
Max |
Unit |
Notes |
Temperature monitor absolute error |
DMI_Temp |
-3 |
3 |
degC |
Over operating temp |
Laser power monitor absolute error |
DMI_TX |
-2 |
2 |
dB |
|
RX power monitor absolute error |
DMI_RX |
-2 |
2 |
dB |
-1dBm to -16dBm range |
Supply voltage monitor absolute error |
DMI_VCC |
-3 |
3 |
% |
|
Bias current monitor |
DMI_Ibias |
-10% |
10% |
mA |
|
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be specifically confirmed in writing by F-tone Networks before they become applicable to any particular order or contract. In accordance with the F-tone Networks policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of F-tone Networks or others. Further details are available from any F-tone Networks sales representative.